Willkommen auf SVrider 
 
 
 
 Daten zum Eintrag von SV.MK
 
 Name : Dirk
 Stadt : Letmathe
 Land : Deutschland
 
 Modell  :  Pontiac Fiero Baujahr 1986 (1 kW)
 Farbe  :  Weiss
 Kilometerstand des Motorrades  :  139000 km
 Kilometer / Jahr  :  5000 km im Jahr
 
 Letzte Änderung am  :  15 Oct 2011 17:07
 
 Bewertung
 
  Bewertung gesamt   Bewertung letzte 12 Monate   Bewertung letzte 6 Monate
      Keine Bewertungen    Keine Bewertungen 
  Anzahl: 3   Anzahl: 0   Anzahl: 0
 Vorgenommene Umbauten
 
 s:
86 GT with 139K miles and a 5 speed Getrag / ac / pw / cruise / white with gray interior / only 3K + miles on the car since rebuilt everything

Still could use a paint job but not bad. Also the AC is not hooked up. I have new components for it and the ac line has been modified just not installed. The compressor is installed.

COOLING SYSTEM
Radiator has been cleaned out
New Driver side coolant tube from Fiero Store
All new hoses up front
New fan motor

SUSPENSION
Front
All suspension component removed --- cleaned and painted
All bushing replaced with poly
New lowering front springs from West Coast
New front sway bar from Fiero Store
Reman steering rack from Fiero Store
All new tie rods
All new tie rod ends
All new ball joints
New bearings
New KYB shocks

Rear
All components removed, cleaned and painted
All bushings replaced with poly
Aluminum cradle bushings
New rear tie rods
New rear tie rod end
New rear hubs
New KYB struts converted to Coil-overs
New Fiero Store rear sway bar
New half shafts

TIRES / WHEELS
New TSW Snetterton 17" wheels
New 452 Falken tires 225/45R17 front, 255/45R17 rear

BRAKES
All New SS Brake Lines from Fiero Store
11.25 UPGRADE ------ works great!
All new Rotors
New calipers
New pads

ENGINE
98 3800 SC II from a GTP
ECM by Loyde @ FastFieros
All new engine bearings (cam / crank / rod / etc)
New rings
All ARP fasteners
XP Cam from ZZP
New duel timing chain ZZP
Ported and Polished Lower Intake mani
Head ported and polished
New valve seals
New springs from ZZP
Bored and polished throttle body
New super thin throttle plate
Matched blower opening to throttle body and smoothed all surfaces for better flow
Boost by pass deleted and hole filled and smoothed
Inner-cooler ----- custom build simular to the ZZP Stag II
3.0 Pulley
Custom Billet Aluminum valve covers (Jet Hot Coated)
Custom built headers 1.75 tubing and Ceramic coated (Jet Hot)
SPEC 3 clutch
Poly mounts and custom dogbone

Head Light Motors have been rebuild and work good

**** HP TUNER Software included ---- about $500 valvue
**** MR MIKES seats
**** All gages work ------- I have three (Rally Style) AutoMeter gages above the radio --- Boost / Volt / Oil

Car is very fast and runs great------- 0 KR when scanning


New Marker Lights Included --- just have not installed them

OK ----- So there it is ------ it has been alot of work but also alot of fun. I need to thank everyone here for helping directly and indirectly. There is so much collective knowledge in this community that it made this job easy.
 
 Text von SV.MK zum Eintrag
 
SV.MK hat noch keinen Text verfasst.

 Bilder
 
Kommentare:
Pat SP-1
15 Feb 2017 09:23
 
 
Irgendwie sind da zuviele Räder und zuviel Blech für ein Motorrad ´dran...
 



 
Copyright © 2003-2018 by SVrider.de e.V. -- Bisherige Besucher: 6.231.972 -- Besucher Online: 97 -- Impressum -- Datenschutzrichtlinie